Questions on Installation
-
mbunner
- Posts: 6
- Joined: Tue Jan 13, 2009 1:07 am
Post
by mbunner » Tue Jan 13, 2009 1:10 am
I installed without any problems, then added my HP designjet 130 from TurboPrint Control. When printing a test page, my printer beeps then shuts down. Any ideas what I am doing wrong?
Thanks -
-
zedonet
- Site Admin
- Posts: 1781
- Joined: Fri Oct 06, 2006 8:02 am
Post
by zedonet » Wed Jan 14, 2009 8:17 am
Hello,
it seems that changes for newer DesignJet printers cause the problem - I will send you a corrected driver by email.
-
mbunner
- Posts: 6
- Joined: Tue Jan 13, 2009 1:07 am
Post
by mbunner » Wed Jan 14, 2009 1:32 pm
Thanks - that resolved the problem, I can now print! Can you point me to instructions on how to adjust my print margins? The test print and demo page both are printing far off the page on 8-1/2 x 11. Margins in Gimp look fine, resulting print is off the page as well.
-
zedonet
- Site Admin
- Posts: 1781
- Joined: Fri Oct 06, 2006 8:02 am
Post
by zedonet » Wed Jan 14, 2009 3:02 pm
Hello,
thank you for testing!
Can you tell me in which way the print is "off" - e.g. "moved by 0.5 inches to the left and by 0.7 inches to the top"?
-
mbunner
- Posts: 6
- Joined: Tue Jan 13, 2009 1:07 am
Post
by mbunner » Wed Jan 14, 2009 4:12 pm
Looking at the demo print on 8.5x11, it's currently printing about 1.8 inches to the right.
-
mbunner
- Posts: 6
- Joined: Tue Jan 13, 2009 1:07 am
Post
by mbunner » Wed Jan 21, 2009 10:49 pm
Any updates on this one? How can I adjust my margins to get the print on the page?
-
zedonet
- Site Admin
- Posts: 1781
- Joined: Fri Oct 06, 2006 8:02 am
Post
by zedonet » Thu Jan 22, 2009 11:04 am
Hello,
can you install the new version TurboPrint 2.07-1 and test if the problem persists?
-
mbunner
- Posts: 6
- Joined: Tue Jan 13, 2009 1:07 am
Post
by mbunner » Fri Jan 23, 2009 3:09 am
Looking at the printed page right side up, it's still printing about 1.8 inches to the right on both the demo page and test page. The pages come out of the printer upside down, so if I use 11x17 paper the entire print is on the page. I did try creating a custom page under "sizes" using both +1.8 & -1.8 left and it appears to have no impact on the print.
Thanks,
Mark
-
zedonet
- Site Admin
- Posts: 1781
- Joined: Fri Oct 06, 2006 8:02 am
Post
by zedonet » Fri Jan 23, 2009 11:40 am
Hello,
could you send me the log file /var/log/turboprint/print.log after such a print - please email to
mailt (a) turboprint (dt) de
thank you!
-
mbunner
- Posts: 6
- Joined: Tue Jan 13, 2009 1:07 am
Post
by mbunner » Sun Jan 25, 2009 3:17 pm
I sent the log to "mailt (a) turboprint (dt) de" and received:
>><mailt (a) turboprint (dt) de>: host mailin.rzone.de[81.169.145.100]
>> said: 550 5.2.1 Mailbox is blocked (in reply to RCPT TO command)
I resent to "mail (a) zedonet (dt) de" hopefully you got the message, let me know if you didn't.
Mark